Garmin Edge 510 / GSC-10 for Tern Verge P18

2013年12月13日金曜日

どうぐ:アウトドア どうぐ:ガジェット

t f B! P L
Tern Verge P18を手に入れてから、サイコンを物色していました。色々な誘惑と後押しもあり、ずっと気になっていたGarmin Edge 510 with Sensorsを購入しました。非常に高い価格でしたが、Webを検索しているとPBKで、期間限定で非常に安く販売されているのを発見。早速、Wiggleの最低価格保証システムを利用して、最安値のクーポンを発行してもらいました。

Wiggleの対応は非常に遅く一週間以上回答がありませんでしたが、英語で催促メールと画面キャプチャーを送付することですんなりと対応してくれました。

価格が安い一方で、外語表記になりますが、低解像度の液晶に無理やり日本語表示をするよりは、シンプルな英語表示のほうが見やすいと思ってコチラを購入しました。

Garmin Edge 510 with Sensors was just arrived from wiggle UK with the lowest price as compared to PBK and other web sites. I bought this item using the best price coupon by wiggle. Wiggle guarantees the best price for their products. If you may find lower price on other web site, you will get coupon when you just send e-mail to support@wiggle.com with screen capture (need to meet wiggle condition at web site).

TernのWebサイトを見ていると、20インチのサイズにはGarminのGSC-10センサーを付けても反応が無い!との記事がありましたが、色々と試行錯誤したところ問題なく取り付けが完了しました。Brompton、BD-1などに取り付ける場合には、センサーを分離するなど手間が必要とのことですが、今回は電子工作を行うこともありませんでした。

I worried whether Garmin edge 510 was attached to Tern Verge P18 or not due to small side of wheels. Finally, I had no problem to install Garmin GSC-10 sensor for speed meter and cadence.
センサーマグネットはDAISOの100円マグネットに変更するか、写真のようにクランクの端に自己融着テープで括りつけるのが良さそうです。当初、付属のナイロンバンドで固定することも考えましたが、素材が固く上手くタスキ掛けに取り付けるのは難しいと思いやめました。

Of course, the position of Garmin GSC-10 on Tern Verge P18 was very sensitive. So, need some technique to attach cadence magnet on crank. When the crank magnet is attached on the end of left crank, it is very difficult to use nylon band for fixing. I used self-fusing tape
Another issue to install the cadence magnet on left crank was clearance between left crank with magnet and bicycle stand. There is jut a few millimeters. So I attached the cadence magnet on the edge of left crank. I also found that I could replace the magnet from Garmin original cadence magnet to super strong magnets (13mm, 200Gs). It was 100 yen (almost 1UDS) for four magnets.

ケイデンスのマグネットをクランクエンドに取り付けたおかげで、Garmin GSC-10の接続場所に余裕が出来ました。

The Garmin GSC-10 position was also sensitive. I hope these pictures help your installation.
ナイロンバンドの位置は、Ternのロゴの横を通るようにするのがミソです!ナイロンバンドの下にはフレーム保護のために、透明の保護シートを貼り付けています。実は、Garmin GSC-10の電池の場所はタイヤ側になりますので、通所は電池交換の際にホイールを外す必要が出てきます。

そんな面倒なことはやってられない!とのことで、Garmin GSC-10センサーを手前に90度回転させて、電池を交換しようと考えています。そんな訳で、保護シートを貼ることで、センサー回転時に、フレームに傷がつかないように配慮してみました。

A rough position indication is the print of "tern"
当初Garminの純正マグネットを取り付けていましたが、ネジ式で落下の不安があったため、DAISOマグネットに変更しました。こちらも自己融着テープを使って取り付け見た目がスッキリしました。

本当は二六製作所さんの角型ネオジムマグネットを買うことも考えていましたが、帰り道にDAISOで試作してみよう!と取り付けたら、「これもありかな!」と妥協しました。

Initially, I used the Garmin original speed magnet. I, however, changed the magnet to the super strong magnets mini (6mm, 2800Gs) because the original speed magnet is easy to lose.
It was also 100 yen (almost 1USD) for 8 magnets.

ということで、ロードでもないポタ用バイクにGarminをインストールしてみました。




New

Apple M1チップでデュアルディスプレイ!トリプルディスプレイ!

M1チップを搭載したMacBook Airでデュアルディスプレイ、トリプルディスプレイを構築!    2020年11月11日に発売されたM1チップ搭載MacBookAir、MacBook Proは、2台以上の外部ディスプレイに映像を出力することができない制約があります。 しかし、...

Search

Contact

名前

メール *

メッセージ *

QooQ